Backing Up a Solaris System With Installed Zones

The following procedures can be used to back up files in zones. Remember to also back up the zones' configuration files.

How to Use `ufsdump` to Perform Backups

You can perform full or incremental backups using the ufsdump command. This procedure backs up the zone /export/my-zone to /backup/my-zone.ufsdump, where my-zone is replaced with the name of a zone on your system. You might want to have a separate file system, for example, a file system mounted on /backup, to hold the backups.

Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see Using the Solaris Management Tools With RBAC (Task Map) in System Administration Guide: Basic Administration.
(Optional) Shut down the zone to put the zone in a quiescent state and to avoid creating backups of shared file systems.
```
global# zlogin -S my-zone init 0
```

Check the zone's status.

global# zoneadm list -cv

You will see a display similar to the following:

ID  NAME     STATUS       PATH                           BRAND      IP
 0  global   running      /                              native     shared
 -  my-zone  installed    /export/home/my-zone           native     shared

Perform the backup.

global# ufsdump 0f /backup/my-zone.ufsdump /export/my-zone

You will see a display similar to the following:

DUMP: Date of this level 0 dump: Wed Aug 10 16:13:52 2005
DUMP: Date of last level 0 dump: the epoch
DUMP: Dumping /dev/rdsk/c0t0d0s0 (bird:/) to /backup/my-zone.ufsdump. 
DUMP: Mapping (Pass I) [regular files]
DUMP: Mapping (Pass II) [directories]
DUMP: Writing 63 Kilobyte records
DUMP: Estimated 363468 blocks (174.47MB).
DUMP: Dumping (Pass III) [directories]
DUMP: Dumping (Pass IV) [regular files]
DUMP: 369934 blocks (180.63MB) on 1 volume at 432 KB/sec
DUMP: DUMP IS DONE

Boot the zone.
```
global# zoneadm -z my-zone boot
```

How to Create a UFS Snapshot Using `fssnap`

This approach uses the fssnap command, which creates a temporary image of a file system intended for backup operations.

This method can be used to provide a clean, consistent backup of the zone files only, and it can be executed while zones are running. However, it is a good idea to suspend or checkpoint active applications that are updating files when the snapshot is created. An application updating files when the snapshot is created might leave these files in an internally inconsistent, truncated, or otherwise unusable state.

In the example procedure below, note the following:

There is a zone named my-zone under /export/home.
/export/home is a separate file system.

Before You Begin

The destination backup is /backup/my-zone.ufs. You must create the directory backup under /.

Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see Using the Solaris Management Tools With RBAC (Task Map) in System Administration Guide: Basic Administration.
Create the snapshot.
```
global# fssnap -o bs=/export /export/home
```
You will see a display similar to the following:
```
dev/fssnap/0
```
Mount the snapshot.
```
global# mount -o ro /dev/fssnap/0 /mnt
```

Back up my-zone from the snapshot.

global# ufsdump 0f /backup/my-zone.ufsdump /mnt/my-zone

You will see a display similar to the following:

DUMP: Date of this level 0 dump: Thu Oct 06 15:13:07 2005
   DUMP: Date of last level 0 dump: the epoch
   DUMP: Dumping /dev/rfssnap/0 (pc2:/mnt) to /backup/my-zone.ufsdump.
   DUMP: Mapping (Pass I) [regular files]
   DUMP: Mapping (Pass II) [directories]
   DUMP: Writing 32 Kilobyte records
   DUMP: Estimated 176028 blocks (85.95MB).
   DUMP: Dumping (Pass III) [directories]
   DUMP: Dumping (Pass IV) [regular files]
   DUMP: 175614 blocks (85.75MB) on 1 volume at 2731 KB/sec
   DUMP: DUMP IS DONE

Unmount the snapshot.
```
global# umount /mnt
```
Delete the snapshot.
```
global# fssnap -d /dev/fssnap/0
```
Note that the snapshot is also removed from the system when the system is rebooted.

How to Use `find` and `cpio` to Perform Backups

Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see Using the Solaris Management Tools With RBAC (Task Map) in System Administration Guide: Basic Administration.
Change directories to the root directory.
```
global# cd /
```

Back up my-zone files that are not loopback mounted to /backup/my-zone.cpio.

global# find export/my-zone -fstype lofs -prune -o -local | cpio -oc -O /backup/my-zone.cpio type as one line

Verify the results.

global# ls -l backup/my-zone.cpio

You will see a display similar to the following:

-rwxr-xr-x   1 root     root     99680256 Aug 10 16:13 backup/my-zone.cpio

How to Print a Copy of a Zone Configuration

You should create backup files of your non-global zone configurations. You can use the backups to recreate the zones later if necessary. Create the copy of the zone's configuration after you have logged in to the zone for the first time and have responded to the sysidtool questions. This procedure uses a zone named my-zone and a backup file named my-zone.config to illustrate the process.

Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see Using the Solaris Management Tools With RBAC (Task Map) in System Administration Guide: Basic Administration.
Print the configuration for the zone my-zone to a file named my-zone.config.
```
global# zonecfg -z my-zone export > my-zone.config
```